SEVEN SEGMENT DENGAN ARDUINO IDE

I.TUJUAN

-Siswa dapat menggunakan arduinoIDE
-Siswa dapat merangkai rangkaian di protoboard
-Siswa dapat memprogram di arduinoIDE
-Siswa dapat membuat variasi program di sevensegmen

II.ALAT DAN BAHAN

-Sevensegment
-Arduino IDE
-Laptop/PC
-Jumper
-Protoboard
-Resistor
-Pushbutton

III.DESKRIPSI TUGAS

-Membuat program Arduino menggunakan sevensegment dan dengan 2 tombol up dan down

IV.LANGKAH KERJA

-Buat program di arduinoIDE
-Tulis program ini :
int A = 2;
int B = 3;
int C = 4;
int D = 6;
int DP = 5;
int E = 7;
int F = 8;
int G = 9;

int switchUpPin = 13;
int switchDownPin = 12;
int counter = 0;
int buttonUpState = 0;
int lastButtonUpState = 0;
int buttonDownState = 0;
int lastButtonDownState = 0;

void setup() 
{
  Serial.begin(9600);
  
  pinMode(A, OUTPUT);
  pinMode(B, OUTPUT);
  pinMode(C, OUTPUT);
  pinMode(D, OUTPUT);
  pinMode(E, OUTPUT);
  pinMode(F, OUTPUT);
  pinMode(G, OUTPUT);
  pinMode(DP, OUTPUT);

  digitalWrite(DP ,HIGH);
}

void loop() 
{
  buttonUpState = digitalRead(switchUpPin);
  buttonDownState = digitalRead(switchDownPin);

  if (buttonUpState != lastButtonUpState) 
  {
    if (buttonUpState == HIGH) 
    {
      if(counter == 9)
      {
        counter = -1;
      }
      counter++;
      Serial.println(counter);
      changeNumber(counter);
      delay(300);
    }
    else
    {
        Serial.println("OFF");
    }
   delay(50);
  }


  if (buttonDownState != lastButtonDownState) 
  {
    if (buttonDownState == HIGH) 
    {
      if(counter == 0)
      {
        counter = 10;
      }
      counter--;
      Serial.println(counter);
      changeNumber(counter);
      delay(300);
    }
    else
    {
        Serial.println("OFF");
    }
   delay(50);
  }
  changeNumber(counter);
}


void changeNumber(int buttonPress)
{
  switch (buttonPress)
  {
    case 0:
      digitalWrite(A,HIGH);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, HIGH);
      digitalWrite(E, HIGH);
      digitalWrite(F, HIGH);
      digitalWrite(G, LOW);
      break;
    
    case 1:
      digitalWrite(A, LOW);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, LOW);
      digitalWrite(E, LOW);
      digitalWrite(F, LOW);
      digitalWrite(G, LOW);
      break;
    
    case 2:
      digitalWrite(A, HIGH);
      digitalWrite(B, HIGH);
      digitalWrite(C, LOW);
      digitalWrite(D, HIGH);
      digitalWrite(E, HIGH);
      digitalWrite(F, LOW);
      digitalWrite(G, HIGH);
      break;
    
    case 3:
     digitalWrite(A, HIGH);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, HIGH);
      digitalWrite(E, LOW);
      digitalWrite(F, LOW);
      digitalWrite(G, HIGH);
    break;
    case 4:
      digitalWrite(A, LOW);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, LOW);
      digitalWrite(E, LOW);
      digitalWrite(F, HIGH);
      digitalWrite(G, HIGH);
      break;
    
    case 5:
      digitalWrite(A, HIGH);
      digitalWrite(B, LOW);
      digitalWrite(C, HIGH);
      digitalWrite(D, HIGH);
      digitalWrite(E, LOW);
      digitalWrite(F, HIGH);
      digitalWrite(G, HIGH);
      break;
    
    case 6:
      digitalWrite(A, HIGH);
      digitalWrite(B, LOW);
      digitalWrite(C, HIGH);
      digitalWrite(D, HIGH);
      digitalWrite(E, HIGH);
      digitalWrite(F, HIGH);
      digitalWrite(G, HIGH);
      break;
    
    case 7:
      digitalWrite(A, HIGH);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, LOW);
      digitalWrite(E, LOW);
      digitalWrite(F, LOW);
      digitalWrite(G, LOW);
      break;
    
    case 8:
      digitalWrite(A, HIGH);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, HIGH);
      digitalWrite(E, HIGH);
      digitalWrite(F, HIGH);
      digitalWrite(G, HIGH);
      break;
    
    case 9:
      digitalWrite(A, HIGH);
      digitalWrite(B, HIGH);
      digitalWrite(C, HIGH);
      digitalWrite(D, HIGH);
      digitalWrite(E, LOW);
      digitalWrite(F, HIGH);
      digitalWrite(G, HIGH);
      break;
  }

}

-Setelah selsai lalu hubungkan ke laptop/pc 

-Selesai,silahkan mencoba.

V.HASIL KERJA

VI.KESELAMATAN KERJA

-Memakai wearpack

-Menaati aturan lab

-Menggunakan alat sesuai fungsi

VII.KESIMPULAN

 

   Dalam praktek ini kita belajar untuk membuat program seven segment counter up dan down dengan dua tombol pushbutton.Kesulitan saya saat praktek adalah ketika membuat program saat membuat angka di seven segment kadang ada yang kebalik-kebalik.

Mengetahui

 

                                                                              klaten 25 Januari 2017 

Pembimbing                                                          Penulis

(Y.Prasetya Adi Nugroho)                             (Aditya Hermawan)

 

Membuat Program Arduoino Flip-Flop dengan 2 Tombol

I.TUUJUAN

-Siswa dapat menggunakan Arduiono IDE
-Siswa dapat membuat program variasi dengan Arduino IDE
-Siswa dapat membuat program Arduino dengan 2 tombol

II.ALAT DAN BAHAN

-LED
-Arduino IDE
-Laptop/PC
-Jumper
-Protoboard
-Resistor

III.DESKRIPSI TUGAS

-Membuat program Arduino menggunakan 2 tombol dengan lampu flip-flop

IV.LANGKAH KERJA

- Buat program di Arduino
-Tulis program ini.;

 

int Btn2;

  int pin = 2;

  int off = 3;

  int Button;

  int Out = 13;

  int Out1 = 12;

void setup() {

  pinMode(pin,INPUT);

  pinMode(Out,OUTPUT);

  pinMode(off,INPUT);

  pinMode(Out1,OUTPUT);

}

void loop() {

  // put your main code here, to run repeatedly:

  ul:

  Button=digitalRead(pin);

  if(Button == HIGH){

    flip();

  }  

  goto ul;

}

void flip(){

  ulang:

  digitalWrite(Out,HIGH);

  delay(100);

  digitalWrite(Out,LOW);

  delay(100);

  digitalWrite(Out1,HIGH);

  delay(100);

  digitalWrite(Out1,LOW);

  delay(10);

  Btn2=digitalRead(off);

  if(Btn2 == HIGH){

    digitalWrite(Out,LOW);

    digitalWrite(Out1,LOW);

    loop();

  }

  goto ulang;

}

-Setelah selesai masukkan port ke laptop/Pc lalu uploadf dan coba

V.HASIL KERJA

VI.KESELAMATAN KERJA

-Memakai wearpack

-Menaati aturan lab

-Menggunakan alat sesuai fungsi

VII.KESIMPULAN

Dalam praktek ini kita diajarkan untuk membuat program Arduino IDE dengan menggunakan 2 tombol dengan mengisi program di Arduino IDE terlebih dahulu,Setelah selesai lalu upload dan lihat hasilnya.

MENGETAHUI

KLATEN 4 JANUARI 2017

    PEMBIMBING                                                                                            PENULIS

(Y.PRASETYA ADI N)                                                                        (ADITYA HERMAWAN)